| Availability: | |
|---|---|
| Quantity: | |
A stage is only as good as the frame holding it.
On show day, a truss disappears behind the lights and the banners. Nobody notices it until something goes wrong — a wobbling spotlight, a crooked span, or a connector that won't seat an hour before doors open. Our aluminum stage truss system is built for crews who set up in a hurry, tear down late at night, and still expect the structure to look straight and feel solid the next morning. It isn't the flashiest part of a production, but everything else depends on it.
Manufacturing — built, not just assembled
Every length of truss starts as 6061-T6 aluminum tube, cut on CNC saws so the ends meet flush instead of leaving the small gaps you get with manual cutting. The diagonal braces are welded by hand by workers who have been doing this for years. A machine can repeat a weld perfectly, but it can't catch a bad bead the way a person can — and on a load-bearing structure, that judgment matters.
After welding, each section goes through a straightening check on a level table and a full visual inspection before it is cleaned and packed. We do not rush this part. A crooked section shows up the moment you try to connect it on site, and by then it is too late to fix quietly.
Surface finish gets the same attention. Depending on the order, the aluminum is natural-anodized or powder-coated, so it resists the chalky oxidation you see on cheaper frames after a single season outdoors. For venues with a fixed visual identity, we can match RAL colors, and when the truss will be visible in photos or on camera, we can add custom plates or engraved logos to the chords. None of this makes the truss stronger, but it is the difference between equipment that looks rented and equipment that looks like it belongs.
Technical advantages — what you get on site
The box-truss design is the reason these sections punch above their weight. Load is spread across four chords rather than concentrated in a single tube, so a given span carries noticeably more than a single-tube frame of the same weight. It also resists twisting, which is what actually kills cheaper truss over time.
Pin connectors or spigots — take your pick — lock sections together without wobble, and the whole thing goes up with basic hand tools. No special rigging hardware, no hydraulic lift required for the smaller spans. Two people can raise a 6-meter span in well under an hour, which on a multi-venue tour is the difference between a manageable call time and an overtime bill.
Because the aluminum doesn't rust, the gear still looks presentable after a rainy outdoor show, and it doesn't add dead weight to your truck or your shipping container. Every section is numbered and the load charts are published, so your crew isn't guessing about what a given configuration can safely carry.
Advantages and value — the long-term math
Buying truss is a long game, and the cheapest quote is rarely the cheapest outcome. Cheap welded frames work fine for a few events, then the connectors start to slop, the finish starts chalking, and you're either shimming on site or explaining to a client why the rig doesn't look as clean as the reference photos.
Ours hold their geometry, which means less time fiddling on site and fewer complaints from the person who paid for a clean look. For rental companies, that translates directly into more bookings per year and a lower replacement bill. A truss that lasts eight seasons instead of three changes the math completely. For a one-off event, it means you can focus on the show instead of worrying about the rig.
The system is modular, too. You are not locked into one layout — buy a few spans now, add more when the work grows, and mix series as your inventory expands.
Applications — where it gets used
You'll find these systems under concert stages, holding lighting arrays at weddings, framing exhibition booths, supporting LED walls, and rigging banners at outdoor festivals. The 290mm and 390mm series cover most small-to-mid venues; heavier shows with larger fixtures step up to the 450mm or 520mm box truss.
One thing crews often overlook is that truss isn't only for holding lights. We've seen the same sections used to build photo booths, hang signage, create archways at the entrance, and even form temporary room dividers at trade fairs. If you can sketch it, there's usually a way to rig it.
Not sure which size fits your load? Send us the span and what you're hanging. We'll tell you straight, including when a smaller truss will do — the right answer isn't always the bigger one.
After-sales service — what happens after the order
Spare parts — pins, spigots, bolts, feet — stay in stock, so a lost connector doesn't ground your next event. That sounds like a small thing until it's 6pm on a Friday and the truck is already loaded.
We answer messages within one working day. If it's your first time with the system, we can walk your crew through assembly over a video call rather than leaving you to decipher a manual. Drawings and load charts go out with every order, and we'll help you build a layout before you commit to a purchase, so you're not guessing about quantities.
Warranty covers manufacturing defects; normal wear items are replaceable at cost, with no argument about whether it was "your fault." When something does go wrong, you get a real person who knows the product, not a ticket number.
Ready to price a setup? Tell us the span, the series, and your port, and we'll send a quote that includes the parts you'll actually need — no hidden connectors, no surprise shipping charges.
No. 1200, Fengyang Road, Weitang Town, Xiangcheng District, Suzhou